Product ID:HYSOL A-4309 ADHESIVE
MSDS Date:05/17/1979
FSC:8040
NIIN:00-235-8357
Kit Part:Y
MSDS Number: BHDCK

Emergency Phone: 716-372-6300

Info Phone: 716-372-6300

Preparer: JAMES P. HORNBURG

Cage: 14347

Telephone: 516-667-1010

Cage: 14347

BISPHENOL A TYPE EPOXY RESIN

CAS: 25068-38-6

RTECS: SL6310000

Fraction By Weight: 80%

ORGANOPHILIC CLAY

Fraction By Weight: 20%

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Effects of Overexposure:INGES: LOW LD 50 (RAT) GREATER THAN 2000 MG/KG.
NORMALLY NO IRRI FROM VAPORS. EYE: MINOR TRANSIENT IRRI. NO CORNEAL
INJURY LIKELY. SKIN: ONLY MINOR IRR; MAY BE A SKIN SENSITIZER,
ABSORBED THROUGH SKIN IN TOXIC AMTS. INHAL: NOT CONSIDERED
APROBLEM UNLESS HEATED TO HIGH TEMP. NONE SUGGESTED

First Aid:EYES: FLUSH WITH WTR. IF ANY ILL EFFECTS DEVELOP, GET MED
ATTN. SKIN: WASH W/SOAP & PLENTY OF WTR. REMOVE CONTAM CLOTHING,
WASH BEFORE REUSE. INHAL: REMOVE PERSON TO FRESH AIR & GET MED
ATTN. INGES: NOT LIKELY A PROBLEM. NO KNOWN ANTIDOTE.TREAT
SYMPTOMATICALLY. INDUCE VOMITING IF LARGE AMOUNTS ARE SWALLOWED.

Flash Point Method:OC
Flash Point:470 F 243 C
Lower Limits:NA
Upper Limits:NA
Extinguishing Media:WATER FOG, FOAM, CO2, DRY CHEMICAL
Fire Fighting Procedures:MASK TO AVOID BREATHING SMOKE
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:COVER WITH ABSORBENT MATERIAL. SCOOP INTO
WASTE CANS

Handling and Storage Precautions:CLEAN, BODY- COVERING CLOTHING.
DISPOSABLE CONTAINERS
Other Precautions:NEVER GIVE FLUIDS OR INDUCE VOMITING IF PERSON IS
UNCONSCIOUS OR HAVING CONVULS-IONS

Respiratory Protection:NONE LIKELY NEEDED
Ventilation:GOOD VENTILATION
Eye Protection:SAFETY GLASSES WITH SIDE SHIELDS
Other Protective Equipment:CLEAN, BODY-COVERING CLOTHING. DISPOSABLE
CONTAINERS AND PAPER ON WORK AREA
Work Hygienic Practices:GENERAL
Supplemental Safety and Health
NK

Boiling Pt:B.P. Text:> 500
Vapor Pres:NIL
Vapor Density:NA
Spec Gravity:1.3
Solubility in Water:NIL
Appearance and Odor:GREENISH TAR HIGHLY VISCOUS LIQUID
Percent Volatiles by Volume:NIL

Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIALS
Stability Condition to Avoid:EXCESS HEATING OVER LONG PERIODS OF TIME
DEGRADES THE RESIN
Conditions to Avoid Polymerization:WHEN MIXED WITH ALIPHATIC AMINES IN
MASSES GREATER THAN 1 LB

Waste Disposal Methods:SOLIDIFY BY MIXING WITH EPOXY HARDENER AND SENT
TOAPPROVED LANDFILL

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.